PRICES EXCLUDE VAT — ADDED IN THE BASKET · SHIPPING ACROSS EUROPE

mm
154575105130 mm

          How to choose a wick

          Three factors decide the choice — the type of candle, the diameter and the wax. Weigh them together, then confirm with a burn test: there is no universal rule.

          01

          Type of candle

          • Containers (glass, tin): pre-waxed wicks with a metal sustainer — TCR, NAT, Stabilo, CL, LX — or wooden wicks.
          • Pillars and moulds: braided wicks sold by the metre — BK, MG ES, LK.
          • Tea lights: TCR tea light wicks.
          Ø mm
          02

          Diameter

          The most important factor. Always measure the inner diameter of the container, wall to wall. Manufacturer charts are for plain candles, without fragrance or dye: with a fragranced vegetable wax, expect to go 1 to 2 sizes up from the generic chart — and more in difficult combinations.

          03

          Wax

          • Vegetable waxes and beeswax: TCR, NAT, Stabilo, ECO, round or tubular braids, or wooden wicks.
          • Mineral waxes (paraffin): LX or flat braids.
          • Rule of thumb: round braids for vegetable and animal waxes, flat braids for mineral waxes.
          Wick too smallThe candle tunnels: the pool never reaches the wall.
          Wick too largeTall flame, smoke, and the candle burns down much faster.
          10–12
          Right wickThe pool covers the full diameter, 10–12 mm deep.
          TCR
          TCR 18/10 · Ø32–38
          1. TCR — wick series
          2. 18/10 — braid reference (size)
          3. Ø32–38 — inner diameter of the container, in mm, for an unscented candle

          Wooden wicks: they crackle, never slump and leave no unpleasant smell when put out — but they are the hardest to get right. Read our wooden wick guide ›

          Preparing and fitting the wick

          The right wick only works if it is fitted properly. These details make a real difference to the burn.

          Centre it

          An off-centre wick burns one side only and, in extreme cases, overheats the glass until it cracks. Use a wick centring tool and keep the wick taut while the wax sets.

          Fix the base

          Keep the metal sustainer at the bottom: it holds the wick upright and stops the flame reaching the base. Fix it with wick stickers or with a thin layer (about 1 mm) of wax poured first.

          5 mm

          Trim before every burn

          Cut the wick to about 5 mm before lighting. Trim when the wax is cold; straighten the wick while it is still soft. Put the candle out with a snuffer rather than blowing — less smoke and soot.

          Wooden wicks

          Add 5–10% vegetable stearin to soft vegetable waxes: it hardens the wax and stops the wooden wick going out. See stearin.

          Braided wicks in beeswax

          Direction matters: fit braided wicks with the “V” of the braid opening upwards, towards the tip of the candle.

          6–10%

          Fragrance load

          The maximum load a wax accepts is rarely needed. Most fragrances perform well between 6 and 10%; too much fragrance clogs the wick and makes soot without improving the throw.

          Wick off-centre or leaning

          Usually a wick set too loosely or not held while the wax set.

          Re-centre it while the wax is still soft; next time use a centring tool and keep it taut.

          Mushrooming — more fixes

          The flame draws up more fuel (wax + fragrance + dye) than it can burn. A pool deeper than 15 mm after 30 minutes is a clear sign.

          Trim 5 mm before every burn, lower fragrance/dye, then go down one size in the same series.

          Tunnel that gets worse

          The pool widens about 2–3 cm per hour — give it time first. Rarely, a wick that is too big also tunnels.

          If going up a size made the pool smaller, go down a size instead. Don't trim shorter than 5 mm.

          Smoke when you put it out

          Blowing the flame out sends up smoke and soot from the glowing wick.

          Use a snuffer, or dip the wick into the melt pool and straighten it.

          Wick positions

          Compare your candle’s flame with these illustrations to identify the problem.

          Ideal position

          Ideal position

          The wick rises straight and curves to the edge of the flame, where it burns away completely at the highest temperature.

          Corkscrew

          Corkscrew

          Uneven tension in the braid, or strands twisted before the wick was fitted.

          Too thick

          Too thick

          Flame too large for the diameter, with soot. → Go down one size.

          Too upright

          Too upright

          It does not curl, so the tip never reaches the hottest zone and mushrooms. Cause: paper threads in the core, or hard waxes, additives, dyes and fragrances clogging it.

          Too thin

          Too thin

          It melts more wax than it can burn; the pool fills up and may overflow. → Go up one size.

          Falls over

          Falls over

          The wick was set too loosely or had too much room when pouring. → Centre it and keep it taut.

          Too short

          Too short

          Damaged by impurities (pigments, synthetic waxes, fragrance): the flame shrinks and the candle may go out.

          Smokes

          Smokes

          This smoke comes from draughts. → Burn the candle away from draughts.

          Bends too far

          Bends too far

          Soft paraffin or a wick without the right treatment; common in pressed candles.

          Residual ash

          Residual ash

          Impurities in the wax collect at the tip as threads, sometimes like a second wick.

          Temperature zones of a candle flame

          Flame zones

          1. Candle body with the liquid wax pool.
          2. Wick, curved to the edge of the flame with a glowing tip.
          3. Blue zone: base of the flame, plenty of oxygen, faint glow.
          4. Dark zone (600–1000 °C): the fuel vaporises; low oxygen, carbon particles form.
          5. Primary reaction zone: very hot oxidation, up to 1400 °C, almost complete combustion.
          6. Luminous zone: carbon particles glow yellow and burn off on contact with oxygen.

          Illustrations and technical information: WEDO wicks (wedobraids.com)

          All about wicks

          How to choose, fit and test your wick, find your baseline wick, and read the flame — with illustrations.

          Read the wick guide ›
          Choose your wax here
          −1✓+1≥10 cm≥10 cm4 h20–25 °C

          The test at a glance: three identical candles — the recommended wick (✓), one size down (−1) and one up (+1) — at 20–25 °C, at least 10 cm apart, in 4-hour cycles.

          Know the wick series

          Each series is built for a type of wax. Knowing how it is made helps you understand why the calculator recommends it.

          TCR and NAT

          TCR and NAT

          Flat-braided cotton with paper filaments, coated for rigidity. Unbleached and with no chemical treatment. It curls slightly at the tip, which reduces mushrooming, smoke and soot. NAT is the same wick coated in vegetable wax: wherever one works, so does the other. Both are made in Europe, comply with REACH and RAL-GZ 041 and contain no SVHC substances such as boric acid or borax; the cotton is OEKO-TEX® 100 certified.

          Best forviscous vegetable waxes — soy, rapeseed, sunflower — in containers and pillars. It copes well with high fragrance loads and cosmetic candles with shea butter.
          View wicks ›
          Stabilo

          Stabilo

          Coreless flat braid in cotton with paper filaments, pre-waxed at a high temperature. It curls into the hottest part of the flame and burns cleanly.

          Best foran all-rounder — paraffin, vegetable waxes and gel. In vegetable waxes, expect to go 1 to 3 sizes up from paraffin.
          View wicks ›
          LX

          LX

          Coreless flat braid with stabilising threads that keep a slight curl. It gives a controlled flame: the glass does not overheat on one side and pillars do not blow out through the wall.

          Best forparaffin, paraffin blends and coconut wax. In other vegetable waxes it usually needs 1 to 3 sizes up.
          View wicks ›
          VRL

          VRL

          High-grade cotton with white stabilising filaments — the wick stays white in the candle. Treated to cope with solid colours and fragrance loads up to about 10%.

          Best forcontainer candles with a high share of vegetable wax, especially coconut and coconut blends.
          View wicks ›

          Construction matters

          Tighter braid, less waxTwo wicks with the same cotton can burn differently: a tighter braid draws less fuel than a looser one.
          Built for paraffin or for vegetable waxA wick designed for paraffin needs to go up in size in a vegetable wax. The other way round, a wick designed for vegetable waxes is often too big in paraffin.
          Cored wicks mushroom moreThe core makes the wick rigid, but the tight braid clogs more easily and burns in a cooler part of the flame — so carbon builds up at the tip.

          Sources: HowtoMakeCandles.info, Rustic Escentuals, Atkins & Pearce, Wedo and Monterosa Zelandi.

          Wooden wicks: width and thickness

          With a wooden wick, the width is chosen by the container diameter and the thickness by the wax. A wick too wide or too narrow leads to tunnelling, soot and smoke.

          Inner diameterReference widthIn our shop
          38–51 mm6.4 mmEA 1 / EC 1 · 8 mm (our narrowest)
          51–64 mm9.5 mmEA 2 / EC 2 · 10 mm
          64–76 mm12.7 mmEA 3 / EC 3 · 12 mm
          76–89 mm15.9 mmEA 4 / EC 4 · 14 mm or EA 5 / EC 5 · 16 mm
          above 89 mm19 mm or moreuse 2 wicks

          Reference widths: Wooden Wick Co. They are a starting point — always confirm with a burn test.

          Thickness by wax

          EA · 0.6 mmParaffin, paraffin-soy blends and blends with coconut or palm oil — waxes that burn easily.
          EC · 1 mm100% soy, rapeseed and beeswax — more viscous waxes that need more combustion.
          Booster · LA to LDA wick with an extra layer that boosts the flame. Useful in beeswax and soy, when a single wick goes out or tunnels.